[2026-10-30T10:01:49.334Z] [info] SUT version: v1.0.0 [2026-10-30T10:01:49.334Z] [info] Connecting to USB Configuration Link [2026-10-30T10:01:49.337Z] [info] Successfully established connection with the USB Configuration Link (USB device /dev/ttyUSB0) [2026-10-30T10:01:49.337Z] [info] Connected to USB Configuration Link [2026-10-30T10:01:49.337Z] [info] Starting wearable start-up sequence [2026-10-30T10:01:49.848Z] [info] Wearable Unique Device ID: 0447323532363232004A0036 [2026-10-30T10:01:49.857Z] [info] Wearable start-up checks were completed in less than 10 seconds [2026-10-30T10:01:49.857Z] [info] STARTUP_CHECKS_DONE_CP_STATE = completed [2026-10-30T10:01:49.857Z] [info] STARTUP_CHECKS_TIMEOUT_CP_STATE = allocated time not reached [2026-10-30T10:01:49.857Z] [info] BANK1_INVALID_CP_STATE = valid [2026-10-30T10:01:49.857Z] [info] BANK2_INVALID_CP_STATE = valid [2026-10-30T10:01:49.857Z] [info] RUN_BANK_CP_STATE = Bank 1 [2026-10-30T10:01:49.857Z] [info] FW_NOT_COMP_STATE = compatible [2026-10-30T10:01:49.857Z] [info] WPT_INVALID_CP_STATE = in allowed range [2026-10-30T10:01:49.857Z] [info] RFON_INVALID_CP_STATE = valid [2026-10-30T10:01:49.857Z] [info] ENABLE_RFON_INVALID_CP_STATE = valid [2026-10-30T10:01:49.868Z] [info] Current Firmware Version and Hardware Identifiers: [2026-10-30T10:01:49.868Z] [info] Bank number = 0 [2026-10-30T10:01:49.868Z] [info] FW Version = 1.1.0 [2026-10-30T10:01:49.868Z] [info] FW Product Identifier = 5344 [2026-10-30T10:01:49.868Z] [info] FW Subsystem Identifier = 4350 [2026-10-30T10:01:49.868Z] [info] FW Compatibility version = 01 [2026-10-30T10:01:49.868Z] [info] MCU Product Identifier = 5344 [2026-10-30T10:01:49.868Z] [info] MCU Subsystem Identifier = 4350 [2026-10-30T10:01:49.868Z] [info] MCU HW version = 01 [2026-10-30T10:01:49.885Z] [info] Wearable firmware build identity: 1.1.0-dev+b1510.g5ba050d (bank 0, 17988 bytes, CRC32 0x8A006F45) [2026-10-30T10:01:49.885Z] [info] Wearable start-up sequence completed [2026-10-30T10:01:49.885Z] [info] Starting implant start-up sequence [2026-10-30T10:01:49.893Z] [info] Implant powered-on [2026-10-30T10:01:52.446Z] [info] Implant start-up checks were completed in less than 10 seconds [2026-10-30T10:01:52.446Z] [info] IMP_FW_STATE_STARTUP_CHECKS_DONE = completed [2026-10-30T10:01:52.446Z] [info] IMP_FW_STATE_BANK1_INVALID = valid [2026-10-30T10:01:52.446Z] [info] IMP_FW_STATE_BANK2_INVALID = valid [2026-10-30T10:01:52.446Z] [info] IMP_FW_STATE_RUNNING_BANK = Bank 1 [2026-10-30T10:01:52.447Z] [info] IMP_FW_STATE_BANKS_DIFF = identical [2026-10-30T10:01:52.447Z] [info] IMP_FW_STATE_NOT_COMP_WITH_HW = compatible [2026-10-30T10:01:52.447Z] [info] IMP_FPGA_STATE_STARTUP_CHECKS_DONE = completed [2026-10-30T10:01:52.447Z] [info] IMP_FPGA_STATE_BITSTREAM_INVALID = valid [2026-10-30T10:01:52.447Z] [info] IMP_SENSORS_STATE_STARTUP_CHECKS_DONE = completed [2026-10-30T10:01:52.447Z] [info] IMP_SENSORS_STATE_IMPLAUSIBLE_TEMPERATURE = implausible [2026-10-30T10:01:52.518Z] [info] Implant Unique HW ID: 04473235323632320045002E [2026-10-30T10:01:52.588Z] [info] Implant HW Revision ID FW: 5344494D02. Implant HW Revision ID FACTORY: 5344494D02 [2026-10-30T10:01:52.588Z] [error] Implant start-up sequence failed because at least one of the MCUs Firmware states is invalid [2026-10-30T10:01:52.900Z] [info] Implant firmware build identity: 1.1.0-dev.ablapp-1502-keepalive-7s+b1413.gb44b676 (bank 0, 21572 bytes, CRC32 0x08E3E045) [2026-10-30T10:01:53.000Z] [info] Implant FPGA bitstream: 135180 bytes, CRC32 0x36CA5CDD [2026-10-30T10:01:53.000Z] [info] Implant start-up sequence completed [2026-10-30T10:01:53.000Z] [info] Starting implant update sequence [2026-10-30T10:01:53.054Z] [info] Current firmware: v1.1.0, active bank: 0 [2026-10-30T10:01:53.054Z] [info] Target firmware CRC: 0x08E3E045 [2026-10-30T10:01:53.118Z] [info] Bank 1 has target firmware: yes [2026-10-30T10:01:53.262Z] [info] Rebooting to switch to bank 1 [2026-10-30T10:01:58.817Z] [info] Current firmware: v1.1.0, active bank: 1 [2026-10-30T10:01:59.030Z] [info] Bank 1 firmware build identity: 1.1.0-dev.ablapp-1502-keepalive-7s+b1413.gb44b676 (bank 1, 21572 bytes, CRC32 0x08E3E045) [2026-10-30T10:01:59.093Z] [info] Bank 0 has target firmware: yes [2026-10-30T10:01:59.204Z] [info] Rebooting to switch to bank 0 [2026-10-30T10:02:04.754Z] [info] Current firmware: v1.1.0, active bank: 0 [2026-10-30T10:02:04.969Z] [info] Bank 0 firmware build identity: 1.1.0-dev.ablapp-1502-keepalive-7s+b1413.gb44b676 (bank 0, 21572 bytes, CRC32 0x08E3E045) [2026-10-30T10:02:04.969Z] [info] Both banks are up-to-date [2026-10-30T10:02:04.969Z] [info] Implant update sequence completed [2026-10-30T10:02:04.969Z] [info] Starting FPGA update sequence [2026-10-30T10:02:04.972Z] [info] Target FPGA CRC: 0xA50ED517 [2026-10-30T10:02:06.520Z] [info] FPGA has target flash memory: no [2026-10-30T10:02:06.520Z] [info] Starting update of FPGA flash memory [2026-10-30T10:02:06.520Z] [info] Update progress: 0% [2026-10-30T10:02:25.429Z] [info] Update progress: 10% [2026-10-30T10:02:44.122Z] [info] Update progress: 20% [2026-10-30T10:03:02.776Z] [info] Update progress: 30% [2026-10-30T10:03:21.417Z] [info] Update progress: 40% [2026-10-30T10:03:40.058Z] [info] Update progress: 50% [2026-10-30T10:03:58.698Z] [info] Update progress: 60% [2026-10-30T10:04:17.284Z] [info] Update progress: 70% [2026-10-30T10:04:36.009Z] [info] Update progress: 80% [2026-10-30T10:04:54.693Z] [info] Update progress: 90% [2026-10-30T10:05:13.259Z] [info] Update progress: 100% [2026-10-30T10:05:14.794Z] [info] FPGA flash memory successfully updated [2026-10-30T10:05:14.795Z] [info] Power cycling FPGA to apply new flash memory [2026-10-30T10:05:18.014Z] [info] Implant FPGA bitstream: 135180 bytes, CRC32 0xA50ED517 [2026-10-30T10:05:18.243Z] [info] Current FPGA flash memory: v3.0 [2026-10-30T10:05:18.243Z] [info] FPGA flash memory update complete, now up-to-date [2026-10-30T10:05:18.251Z] [info] FPGA update sequence completed [2026-10-30T10:05:18.251Z] [info] SUT completed successfully